Silikon-Vakuumschlauch

1 Produkt

  • Silicone Vacuum Hose Silicone Hose Auto Silicone Hoses 3mm x 7mm 1 Metre Blue

    Silicone Vacuum Hose

    Thin Walled High Temp Flexible

    3 Gesamtbewertungen

    Regulärer Preis Ab £1.01
    Angebotspreis Ab £1.01 Regulärer Preis

Silikon-Vakuumschlauch

Vakuumextrudierte Silikonschläuche sind flexible Schläuche, die häufig in einer Vielzahl von Anwendungen eingesetzt werden, darunter medizinische Geräte, Automobilsysteme und Industriemaschinen. Sie bestehen aus einem Polymer auf Silikonbasis, das ihnen mehrere vorteilhafte Eigenschaften verleiht, wie z. B. hervorragende Temperaturbeständigkeit, hohe Flexibilität und gute chemische Beständigkeit.

Zur Herstellung von Silikonschläuchen im Vakuumextrusionsverfahren wird ein Verfahren namens Vakuumextrusion verwendet. Dabei wird das rohe Silikonpolymer erhitzt und gemischt, um eine viskose Flüssigkeit zu erzeugen, die dann durch eine Düse extrudiert und durch eine Reihe von Vakuumkammern gezogen wird, um ein Hohlrohr zu erzeugen. Die Vakuumkammern werden verwendet, um eventuell im Material eingeschlossene Luftblasen zu entfernen, wodurch eine glatte und gleichmäßige Oberfläche des fertigen Schlauchs entsteht.

Einer der Hauptvorteile von vakuumextrudierten Silikonschläuchen ist ihre Haltbarkeit und Beständigkeit gegenüber extremen Temperaturen. Sie halten Temperaturen von -60 °C bis +180 °C stand und sind daher für den Einsatz in heißen und kalten Umgebungen geeignet. Darüber hinaus sind sie UV- und ozonbeständig, was bedeutet, dass sie sich bei Kontakt mit diesen Elementen im Laufe der Zeit nicht verschlechtern oder spröde werden. Dies macht sie zu einer langlebigen und zuverlässigen Wahl für eine Vielzahl von Anwendungen.

What is silicone vacuum hose used for?

It is thin-walled unreinforced silicone tubing for vacuum lines, breathers and signal lines - boost gauge feeds, wastegate and solenoid signal lines, carburettor and manifold vacuum takeoffs, crankcase breathers, and general small-bore pneumatic and laboratory work. It is chosen for heat resistance and long life rather than for pressure capability.

What sizes do you offer?

Thirty size combinations from 3mm x 7mm up to 10mm x 16mm - the first figure is the internal diameter and the second the outside diameter, so you can pick the wall thickness that suits. Lengths run from 1 metre up to a 30 metre full coil, in blue, red, black and clear. Order by internal diameter to match the spigot it pushes onto.

What temperature will it take?

It is VMQ silicone rated from -60C to +180C with short peaks above that. That is far beyond what the rubber or plastic vacuum tubing fitted as standard to most vehicles will manage, which is why original vacuum lines go hard and split near the manifold while silicone stays pliable. It also stays flexible in the cold rather than becoming brittle.

Is it suitable for fuel or oil lines?

No. This is standard VMQ silicone, which swells and degrades in contact with petrol, diesel and oil. Be particularly careful with breather lines - a crankcase breather carries oil mist and will destroy plain silicone over time. For anything carrying hydrocarbons use our fluorosilicone-lined hose, which is made for exactly that job.

It is unreinforced - will it collapse under vacuum?

For normal manifold vacuum and signal-line duty in the sizes offered, no - the wall thickness is chosen to hold its shape. But it is not a reinforced hose, so do not use it on the suction side of a pump, under strong sustained vacuum, or in large diameters where an unreinforced wall will draw shut. For those, use a hose with a wire helix.

Can I use it under boost pressure?

For low-pressure signal lines to a gauge or solenoid it is fine. It is not a pressure hose and should not be used for charge air, coolant under pressure, or anything where a failure matters. If a line is carrying boost rather than merely sensing it, use reinforced silicone. Unreinforced tubing will balloon and eventually split under sustained pressure.